Reheat furnaces

Pusher Furnace

Iron & Steel
Reheat furnaces Services Products

Pusher Furnace

The pusher furnace uses a pusher mechanism to move the steel through the furnace. The steel is loaded onto a large tray that is pushed through the furnace by a hydraulic or mechanical system. The main challenges faced by these furnaces are hot erosion and mechanical destruction. Therefore, Calderys has developed specific refractory solutions for these furnaces.

Pusher Furnace A<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace B<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace C<p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace D<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace E<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace F<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace G<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace H<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace I<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace J<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace K<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

Pusher Furnace L<ul> <li>CALDE® CAST LA 55 / CALDE® CAST LM 60 / CALDE® GUN M 60 / CALDE® PLAST SUPERAL AB / CALDE® CAST NA 55 QD in standard working conditions</li> <li>CALDE® CAST NM 60 QD / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB / CALDE® GUN SUPEREAL X 70 in case of superior thermal cycling and higher working temperature</li> </ul> <p>Precast solutions are also available</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST M 28 HR / CALDE® CAST LX 50 / CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LX 58 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST AF 470 / CALDE® CAST M 32 HR / CALDE® CAST GIBRAM / CALDE® CAST LX 68 in case of severe condition such as high abrasion</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST LT 90 SP G8 (precast) / CALDE® FLOW UT 92 and CALDE® CAST NT 92 (between rails)</li> <li>Electrofused blocks: ALODUR SURFACAST SGM (Mullite) / ALODUR SURFACAST SG1 (Corundum) / ALODUR SURFACAST SG20M (Zr based)</li> </ul> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 can be used successfully for roof repair and nose installation</li> <li>CALDE® CAST LB 70 C/R: plastic to cast for roof repair.</li> </ul> <p>Full Precast roof solutions are available.</p> <p>Preheating zone:</p> <ul> <li>CALDE® CAST MW 142 / CALDE® CAST M 23 / CALDE® CAST M 28 HR in standard working conditions</li> <li>CALDE® PLAST SUPERAL AB / CALDE® CAST LM 60 / CALDE® CAST MA 55 in case of superior thermal cycling</li> <li>CALDE® GUN M 60 is the best value in use solution</li> </ul> <p>Heating zone:</p> <ul> <li>CALDE® CAST M 30 / CALDE® CAST 1560 / CALDE® CAST LM 60 in standard working conditions</li> <li>CALDE® CAST LX 58 / CALDE® CAST LM 70 / CALDE® PLAST SUPERAL X AB in case of superior thermal cycling</li> <li>CALDE® SOL SPRAYCAST M 74 A as pumpable and quick drying solution</li> <li>CALDE® GUN SUPERAL X 70 is the best value in use solution</li> </ul> <p>Insulation:</p> <ul> <li>We can provide a full range of insulating solutions: Medium Weight (MW) / Light Weight (LW) / Extra Light weight (XL) answering your need and combining both high insulating features and mechanical strength.</li> </ul> <p>Precast solutions are also available for any part: inspection door, thermocouple<br /> sleeves ...</p>

The operating temperature in a pusher furnace is generally up to 1,250°C (for special steel grades like high silicon steel please contact us directly). The stocks (slabs, billets or blooms) move down the length of the furnace. These furnaces are quite popular due to the low installation and maintenance costs compared to other moving furnaces. Main damages are occurring on the refractory hearth by hot erosion and skids protections (hot erosion and mechanical destruction). Calderys has a full range of solutions: cast-in situ, plastic to cast/gun/ram, Quick Drying and Sol-Gel, Spraycast or Precast.

We conduct an extensive audit of your process to design a customised solution from the insulating castables, precast shapes and large range of ceramic anchors in our monolithics portfolio.